Rubber Isolation Mounts (Shock Absorption) - Lockheed Martin Guided Weapon Explosive Ordnance Global Market Scan

Provision of Pavement Materials & Pre-Coated Screenings for Isis Highway at Various Locations Supply & Deliver road paving materials and screenings. REQUIREMENTS & TIMING Location 1: Voss Road Intersection (25 km) Location 2: Foleys Road Intersection (31 km) Location 3: Alfs Road Intersection (33 km) Location 4: Logging Creek Intersection (36.5 km) Location 5: Widening works 30.75-34.5 km The collective quantities required are as follows 10,000 tonne Type 2.1 pavement material 7,500 tonne Type 2.3 pavement material 1,500 tonne CBR10 material 300 tonne 10mm precoated aggregate 500 tonne 14mm precoated aggregate Note: Screenings will be delivered into stockpile. However all paving materials due to the nature of the works (ie narrow widenings) will need to be delivered in sidetippers. Project Specification General All work associated with the Offer shall be performed in accordance with the Department’s Technical Standard: - MRS05 (11/20) – Unbound Pavements - MRS22 (07/20) – Cover Aggregate. - MRS50 (09/20) – Specific Quality System Requirements A copy of these specifications are available from www.tmr.qld.gov.au or by contacting the project manager. Testing Requirements The Offeror shall undertake testing of the material using a NATA Certified Laboratory for the scope of testing required and registered (unconditional) with the Department of Transport and Main Roads as a CMT Supplier. This laboratory shall not subcontract any part of the scope of testing without express approval of the customer. Paving Material – Type 2.1 & 2.3 Maximum 5000 tonne lot Material Property Normal Testing Level Particle size distribution Q103A 1 per 1000 tonne Fines ratio (fines ratio, 0.075mm to 0.425mm sieves) 1 per 1000 tonne Liquid limit – Q104A 1 per 1000 tonne Plastic limit and plasticity index – Q105 1 per 1000 tonne Linear shrinkage – Q106 1 per 1000 tonne Linear shrinkage x% passing 0.425mm sieve 1 per 1000 tonne California bearing ratio – Q113A – ONLY for Type 2.3 1 per 2500 tonne Flakiness index – Q201 1 per 5000 tonne Wet/dry strength variation – Q205C See Note below Degradation factor – Q208B See Note below Ten percent fines value – Q205B See Note below Note: As per the Approved Testing Frequency Level of the Quarry Registration Certificate, for the specific quarry Cover Aggregate Material – For each material property, a minimum of one (1) test result shall be available which is traceable to the material in stockpile. Source Rock Tests: Max Lot Size 5000t Material Property Normal Testing Level Ten percent fines value (wet) – Q205B as per the Approved Testing Frequency Level of the Quarry Registration Certificate, for the specific quarry Wet/dry strength variation – Q205C Degradation factor – Q208B Water Absorption – Q214B Product Tests: Max Lot Size 1000t Particle size distribution - Q103B 1 test per 1000t Flakiness index – Q201 Average least dimension – Q202 Degree of precoating – Q217 Weak particles 2 – Q216 Crushed particles 1, 2 – Q215 1 test per 5000t 1 Required only where aggregate is obtained from other than a blasted quarry face 2 Testing to be undertaken on product prior to pre-coating Material Conversion: - For the purposes of evaluation each Offeror shall include details of the relevant conversion rates of the respective materials.

Provision of Pavement Materials & Pre-coated Screenings Supply & Deliver road paving materials and screenings. REQUIREMENTS & TIMING Location 1: Goodwood Road and Foleys Rd Intersection 1,000 tonne Type 2.1 pavement material 1,500 tonne Type 2.3 pavement material 500 tonne CBR10 material 25 tonne 10mm precoated aggregate 75 tonne 14mm precoated aggregate Note: Screenings will be delivered into stockpile however all paving materials will be delivered directly onto the road. Location 2: Goodwood Road and Garryowen Rd Intersection 250 tonne Type 2.1 pavement material 375 tonne Type 2.3 pavement material 200 tonne CBR10 material 25 tonne 10mm precoated aggregate 75 tonne 14mm precoated aggregate Project Specification General All work associated with the Offer shall be performed in accordance with the Department’s Technical Standard: - MRS05 (11/20) – Unbound Pavements - MRS22 (07/20) – Cover Aggregate. - MRS50 (09/20) – Specific Quality System Requirements A copy of these specifications are available from www.tmr.qld.gov.au or by contacting the project manager. Testing Requirements The Offeror shall undertake testing of the material using a NATA Certified Laboratory for the scope of testing required and registered (unconditional) with the Department of Transport and Main Roads as a CMT Supplier. This laboratory shall not subcontract any part of the scope of testing without express approval of the customer. Paving Material – Type 2.1 & 2.3 Maximum 5000 tonne lot Material Property Normal Testing Level Particle size distribution Q103A 1 per 1000 tonne Fines ratio (fines ratio, 0.075mm to 0.425mm sieves) 1 per 1000 tonne Liquid limit – Q104A 1 per 1000 tonne Plastic limit and plasticity index – Q105 1 per 1000 tonne Linear shrinkage – Q106 1 per 1000 tonne Linear shrinkage x% passing 0.425mm sieve 1 per 1000 tonne California bearing ratio – Q113A – ONLY for Type 2.3 1 per 2500 tonne Flakiness index – Q201 1 per 5000 tonne Wet/dry strength variation – Q205C See Note below Degradation factor – Q208B See Note below Ten percent fines value – Q205B See Note below Note: As per the Approved Testing Frequency Level of the Quarry Registration Certificate, for the specific quarry Cover Aggregate Material – For each material property, a minimum of one (1) test result shall be available which is traceable to the material in stockpile. Source Rock Tests: Max Lot Size 5000t Material Property Normal Testing Level Ten percent fines value (wet) – Q205B as per the Approved Testing Frequency Level of the Quarry Registration Certificate, for the specific quarry Wet/dry strength variation – Q205C Degradation factor – Q208B Water Absorption – Q214B Product Tests: Max Lot Size 1000t Particle size distribution - Q103B 1 test per 1000t Flakiness index – Q201 Average least dimension – Q202 Degree of precoating – Q217 Weak particles 2 – Q216 Crushed particles 1, 2 – Q215 1 test per 5000t 1 Required only where aggregate is obtained from other than a blasted quarry face 2 Testing to be undertaken on product prior to pre-coating Material Conversion: - For the purposes of evaluation each Offeror shall include details of the relevant conversion rates of the respective materials.

Darwin - Defence of Darwin Experience - Replace Sewage Treatment Plant Absorption Trenches & Associated Works

Alice Springs Region - Atitjere Harts Range Health Clinic - Provision of New Leach Absorption Drains